Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Panel Replacement Cost in Knoxville?
Panel replacement in Knoxville typically costs $250 – $500 for a single section, and most homes need one or two sections replaced. The exact figure depends on the door’s brand, the panel material and style, and whether the tracks or hardware took damage at the same time. Every job is priced from a written estimate, so the number on your quote is the number you pay.
That range is for the panel itself and the labor to fit it. A door that lost one section to a hard impact or a bent roller usually lands at the low end. A door that needs a matching custom panel from a manufacturer like Clopay or Amarr will sit toward the top.
Key Takeaways
- Single panel replacement in Knoxville runs about $250 – $500.
- Brand, panel style, insulation, and any track or hardware damage move the number up or down.
- Replacing a section is usually far cheaper than a whole new door, which runs $700 – $2,200.
- Springs, cables, and tracks are priced separately if they’re also worn out.
- Estimates are free, and we work on the brand you already have.
Panel Replacement Cost Breakdown (2026)
Here’s how the typical line items stack up for panel work in the Knoxville area. These are estimated ranges, not final prices. Your written estimate sets the final amount.
| Item | Typical estimated range |
|---|---|
| Single panel replacement (labor + panel) | $250 – $500 |
| Additional matching panel | Quoted per panel on the estimate |
| Roller replacement | $110 – $220 |
| Track realignment | $120 – $240 |
| Cable repair (if the impact stretched or frayed a cable) | $130 – $250 |
| Spring repair (single spring) | $180 – $340 |
| Full garage door repair (broader damage) | $150 – $600 |
| New door installation (if replacement makes more sense) | $700 – $2,200 |
The panel range carries most of the weight. A standard steel panel in a common color and profile sits near the bottom. A custom-order panel matched to a specific brand line pushes toward $500, because the manufacturer has to cut and ship the right section. If your door is a Clopay, Amarr, Wayne Dalton, Craftsman, Raynor, or one of the other leading brands we know well, we can usually source the correct section instead of guessing at a universal fit. That matters in Knoxville, where older homes and newer builds both turn up with doors from a wide spread of manufacturers.
What drives the price up or down comes down to a few things: whether the panel is stock or custom-order, whether it’s insulated, whether the color or texture still matches the rest of the door accurately, and whether the impact that broke the panel also bent a track or damaged a roller. A clean single-panel swap stays low. A panel plus a bent track plus a damaged roller crosses into the broader repair range.
What Affects Panel Replacement Pricing in Knoxville
The cost of panel work here isn’t random. A handful of local factors move it in either direction:
- Brand and model match. Panels aren’t universal. A LiftMaster or Chamberlain opener is separate from the door, but the door panel itself has to match the manufacturer’s profile. Matching a Wayne Dalton or Raynor section takes the right part number, which we can identify on site rather than ordering two or three guesses.
- Panel material and insulation. A basic steel panel costs less than an insulated or textured panel. Knoxville summers are hot and humid while winters swing cold, so an insulated panel holds up better over time and keeps the garage more comfortable, but it does cost more than a bare steel section.
- Color and finish matching. If your door has faded or weathered, a fresh panel in the same factory color can still read slightly different next to older sections. On a very weathered door, some homeowners replace the most visible sections together so the finish reads evenly.
- Hidden damage underneath. A hard impact on a panel often bends a track, cracks a roller, or strains a cable. We check those during the estimate so the price you get reflects the whole job, not just the visible panel.
- Door height and panel count. A tall door with more sections means more material and more labor per panel. A standard single-car door is quicker than a wide double-car door with repeated sections.
- Access and age of the door. A door that’s been sitting with a bent panel for a while can develop rubbing at the tracks. Sorting that out adds time, and older hardware sometimes needs replacing at the same visit.
Knoxville’s mix of housing matters too. The city has a broad spread of neighborhoods, from older homes in the Fourth and Gill area to newer construction out toward Hardin Valley and West Knoxville. Doors from different eras and manufacturers turn up side by side, so being familiar with eight major brands means we can diagnose and source correctly instead of trying to force a mismatched part.
Repair or Replace: Which Makes Sense for Your Door?
Panel replacement is worth it when the door frame, tracks, and springs are still sound and only a section or two is damaged. Replacement makes more sense when the door is old, out of alignment, and showing wear across several sections at once. As a rough guide:
- One or two damaged panels on an otherwise solid door: replace the panels. At $250 – $500 per section, you’re well under the cost of a new door.
- Several panels damaged plus bent tracks and worn springs: a new door in the $700 – $2,200 range often makes more financial sense than chasing repair after repair.
- Cosmetic wear only: if the door still opens and closes smoothly, there may be no urgent need to do anything.
We’ll tell you plainly which way the math points. Repair when repair makes sense, replace when it doesn’t. If you want the fuller picture on how a damaged panel fits into the rest of the system, our Easton Garage Door Service page covers repair, opener work, and installation as three connected services.
How to Save on Panel Replacement
You can keep panel work close to the bottom of the range with a little planning:
- Get an estimate before the damage spreads. A bent panel that rubs against a track can bend the track too. Catching it early keeps the job to one panel instead of a panel plus a realignment.
- Ask about a stock panel where it fits. If your door’s color and profile are common, a stock section costs less than a custom order. We’ll tell you when a stock panel will match and when it won’t.
- Bundle related hardware. If a roller or cable took damage in the same impact, fixing it in one visit saves a second trip. Roller replacement runs $110 – $220 and cable repair $130 – $250 on their own, but combining them with panel work is more efficient.
- Keep the opener out of the equation unless it’s failing. Opener repair ($120 – $320) is a separate job. If your opener is working fine, don’t let panel damage turn into an opener replacement you don’t need.
- Know your brands. We work on the brands you already have, so a matching panel is more likely to be found without a full door swap.
Estimates are free. Call (855) 965-2742 and we’ll look at the door and give you a straight number.
What’s Included in a Panel Replacement Estimate
A good estimate covers more than the panel price. When we look at a door, we check the section itself, the hinges and rollers that hold it, the tracks it rides in, and the balance of the door on its springs. If the impact that broke a panel also nudged a track out of line, that shows up in the estimate as track realignment at $120 – $240, not as a surprise line on the bill later.
We also confirm the opener is still operating the door smoothly after the swap. The opener and the door are one system, and a mismatched section that’s heavier or slightly out of profile can put extra load on the motor. Checking that during the visit is part of doing the job right the first time.
Same-Day Panel Replacement
Panel work often can be done same day when the right section is in stock. If the panel has to be custom-ordered to match your door’s brand and color, there’s a short wait for the part to arrive, and we’ll give you a realistic timeline with the estimate. For a door that’s stuck, off its track, or jammed after an impact, we can make it safe and usable first, then schedule the matching panel.
The door you depend on every day deserves a specialist, not a generalist. If a single section is bent, cracked, or dented and the rest of the door is sound, replacing that section is the repair that makes sense. Our Knoxville service covers panel work, spring repair, cable and track fixes, and opener service in one place, so you’re not coordinating separate contractors for the door and the motor.
Panel Replacement vs. Other Garage Door Repairs
It helps to know how panel pricing compares to the other common jobs, so you can put a quote in context:
- Panel replacement: $250 – $500 for a single section.
- Spring repair: $180 – $340 for one spring. A matched pair is usually replaced together, so a pair costs about twice that.
- Cable repair: $130 – $250.
- Track realignment: $120 – $240.
- Roller replacement: $110 – $220.
- Opener repair: $120 – $320, and opener installation $250 – $550.
- New door installation: $700 – $2,200.
If you’re weighing panel work against a bigger repair, the numbers above give you a frame. A single panel is usually the cheapest way back to a door that looks and works right. When several systems are worn at once, a repair that covers the whole door often costs less over time than patching one part at a time.
Safety Note on Garage Door Work
Garage doors run on high-tension springs and cables under serious load. A door that’s out of balance after an impact can drop fast, and the springs and cables that hold it are genuinely dangerous to touch without the right tools and training. Panel replacement itself looks simple, but getting the door safely into position, keeping the springs under control, and rebalancing it afterward is work for a trained technician. Don’t try to release or adjust springs or cables on your own. If your door is stuck open, jammed, or hanging off a track after damage, call (855) 965-2742 so we can make it safe.
FAQs – Panel Replacement Cost
How much does panel replacement cost in Knoxville?
Panel replacement in Knoxville typically costs $250 – $500 for a single section, labor and panel included. Custom-order panels matched to a specific brand and color sit toward the top of that range, and stock panels sit near the bottom. Call (855) 965-2742 for a free estimate, and the written estimate sets the final price.
Is it cheaper to repair a panel or replace the whole door?
Repairing a single panel at $250 – $500 is far cheaper than a new door at $700 – $2,200. Replacing the whole door only makes sense when several sections are damaged and the tracks and hardware are worn too. Call (855) 965-2742 and we’ll tell you honestly which way the math points.
Can you match my door’s brand and color?
We work on the brands you already have, including LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor, so we can usually source a matching panel. If the door has faded, a new panel in the factory color may read slightly different next to older sections, and we’ll flag that before you commit. Call (855) 965-2742 to confirm your make and model.
Can you come today?
Panel replacement is often done same day when the correct section is in stock. If the panel has to be custom-ordered, there’s a short wait for the part, and we’ll give you a realistic timeline with the estimate. Call (855) 965-2742. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
What else might get damaged when a panel is hit?
A hard impact that bends a panel often bends a track, cracks a roller, or strains a cable. Track realignment runs $120 – $240, roller replacement $110 – $220, and cable repair $130 – $250 as separate jobs. We check all of it during the estimate so the quote reflects the whole job. Call (855) 965-2742 for an exact quote, and estimates are free.
Our technicians have up to 11 years of experience diagnosing doors and openers across the leading brands. From springs to smart openers, we cover the mechanical door and the motor as one system, so you deal with one team instead of two contractors pointing at each other. If your door needs a panel, a track, a spring, or an opener looked at, we’ll give you a clear, written estimate.
Ready for a straight price on your panel replacement? Call (855) 965-2742. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Estimates are free.
Pricing reflects the Knoxville market as of 2026. Easton Garage Door Service offers free estimates – call (855) 965-2742.
Written by the team at Easton Garage Door Service.
What Our Customers Say
"Opener kept reversing halfway down. Turned out to be the safety sensors knocked out of alignment by a bicycle. He straightened them, wouldn't charge me for it, and just asked me to keep them in mind if I need real work later."
- Carlos Herrera"Door installed in about four hours, old one hauled away, and he stayed to program both cars and the wall panel before he left."
- Paige Meyer"Both cables had come off the drum and the door was hanging crooked. I'd watched a video and was about ten minutes from trying it myself, which the tech told me would have been a genuinely bad idea. Glad I called."
- Kurt Ziegler